Forum Replies Created
-
Hi again,
Goal should be to have the BeoSystem 6500 working as it is (and only lend the ML chain the Phono and Tape sources).
And yep, curious what others say.
But after you can get the system wired up with 3 BLCs like below, I am happy to set up an (evening) Teams call and set up all BLCs to get the whole factory running. I now want to see this working :-). Regards, Johan
Hi bnousr, you will need to bring the two new NL sources (A.TAPE and PHONO) to the ML side on your main ML network. I have tried to make more visual Carolpa’s earlier detailed suggestion (to correct if I made a misinterpretation):
As said, I do doubt if there will be no ‘RADIO’ command conflict, if so it could probably be fixed with a 3rd BLC, something like this:
which will be a bit more costly ofcourse. Maybe Carolpa or another more experienced can confirm the above / help to get it more complete to get you where you want to be. Regards, Johan
Hi, I do have a BC6-26(9280), and I do recall that I had to put the ‘HDCP mode’ setting to ‘hdmi’ or ‘disabled’, where ‘HDMI’ worked for my AppleTV
The menu for that is found with Be04 when the ‘cursor’ is at the ‘settings’ position in the TV menu (don’t press GO yet), then press the red arrow button, then press GO.
Go here (sorry it is in Dutch:-))
Then press ‘red arrow’, and then ‘GO’
I am not 100% sure if this is useful, as I understood that not all BV26’s have the ‘hd ready’ kit. But worth a try maybe?
Good luck, Johan
Hi bnousr, I think posting your settings is helping a lot!
In general, I think you should see the BLCs as filters to pass on sources from ML to NL and vice-versa.
In case of the BLC-BS6, the A.Slave setting means you can only pass on sources from its ML side onto NL side. As you only want to pass on the PHONO and the A.TAPE sources, you can ‘uncheck’ in the ‘Experience mapped to NL’ all the boxes apart from ‘N.RADIO’ and ‘A.MEM’ (as they are the same as PHONO and A.TAPE). At ‘Name used on NL’ you can call the N.RADIO source ‘PHONO’, and the ‘A.MEM’ source can be called ‘A.TAPE’. The BLC-BS6 will now pass these sources and commands onto the BLC-BSM that is connected to your main ML network. On the IR mapping page, assign the N.RADIO command to BLC-BS6 with NL source renamed PHONO. The A.MEM command is then to be assigned to BLC-BS6 with renamed NL source A.TAPE.
See my (simple) setting of the BLC connected to my BeoSystem 6500, just for passing on CD onto the NL side:
And the setting of the other BLC to push that CD signal onto its ML side:
As said I am wondering if you cannot better set the BLC-BSM as an A.Slave too, and only pass on the netradio and netmusic onto the main ML network as Carolpa already suggested. I would then assign the ‘RADIO’ IR command to the Beosound Moment’s ‘TuneIn’ NL source, and the ‘N.MUSIC’ (=A.TAPE2) command to the Beosound Moment’s ‘Music’ NL source.
The only thing that I can’t figure out is how the main ML network will react to a ‘RADIO’ IR command, as it might start the TuneIn radio on the BS Moment, as well as the FM radio of the BS9000. Or am I seeing that wrong Carolpa? Were you counting on a 3rd BLC?
bnousr, I hope this helps.
Hallo HuubC, en welkom.
Is het niet een vastgelijmde Masterlink ‘junction box’, om meerdere ML kabels aanelkaar te verbinden? Deze heeft aan beide korte einden twee ronde gaten:
Groet, Johan
