[Tignum]

Do you have speakers connected to the BS6500? If not, my current thought would be to set both BLCs in A.SLAVE mode, as they are only sources. Set the one connected to the BS6500 to map the desired experiences onto NL. In the other BLC, the one in the main MasterLink network, assign those to a logical command (avoiding the earlier mentioned conflicts, which is a bit the ‘pain’ with MasterLink).

 

[bnousr]

Tignum wrote:

Do you have speakers connected to the BS6500?

Yes, do have a pair of Beovox 100 and a Cona connected to the Beomaster which is used regularly but there is no intention to pull audio from the rest of the ML, but rather as mentioned, to distribute the Beogram audio from the BS6500 to the rest of the MasterLink system.

Question, and I’m might just be overthinking this, but with the connection flow going from BS6500 -> 1611 -> BLC -> NL/LAN how does I get the jump from the BLC to the ML. I mean the 1611 is connect with ML cable to the original port in my BLC but can I also use the additional RJ45 ML port; but assume that they’re the same port but just different form factor?

[Tignum]

Hi, yes, just different form factor. So I reckon you can use the BLC as an ‘ML splitter’ if you need to.

Even with using the BS6500 with speakers, I still think that with two audio slave BLCs you can get everything working, if you find enough suitable IR commands. And I am actually quite curious, as I am slowly but seriously planning to add a BeoSound9000 to the mix!

 

[Tignum]

OK, all clear! Was just thinking – bnousr just wants to push BeoGram 6500 audio onto NL, for the main ML system to use it. Couldn’t the speakers stay connected to the BM6500?

I agree that with your solution (an ML amp connected to the main ML chain driving the CXs and the Cona) allows listening to all sources (no need for the 3500 anymore).

Regards, groet, Johan

 

[bnousr]

Followed the discussion, but haven’t had time to test yet as I’ve been busy pulling some CAT7 cable in the house. True the primary objective is to feed the audio from the Beosystem 6500 were the Beogram 6500 to the rest of the house which has my biggest interest, so don’t care about the Radio, CD or the cassette (well tape could be fun if it would be easy and without any conflict of commands being re-used). And as Tignum writes, I still utilise the BS6500 in the office and needs to have the speakers connected directly, and don’t care about audio from any other sources from either ML/NL devices. The office is were I tend to listen to vinyl and occasional CD’s as well and if I listen to vinyl in sometimes I finds it nice to share the analogue wealth with the rest of the household. 🙂

[Carolpa]

Tignum wrote:

So I reckon you can use the BLC as an ‘ML splitter’ if you need to.

Wouldn’t this introduce conflicts? Is a BM6500 with ML chain connected to the BLC or is another ML-chain connected to the BLC?

What would then be the preferred setting? ASlave wouldn’t give the expected result, the same for VMaster. And I doubt SourceCenter or AVmaster will do the trick.

And which ML chain must be connected to which other chain? If the BM6500 and the BS9000 are both on the same ML chain then the BS9000 must be in option 5/6 and will only be a local source.

I would try the next solution, connect:
1. BS9000 (option 0) – ML – BLC – NL ; ASlave ; Set “Experience mapped NL” check CD, name used to “cd9000”; Set “IR mapping” IR command CD to “BS9000 BLC”, “NL source” to “cd9000”.
2. BM6500 (option 0) – T1611 – ML – BLC – NL ; ASlave; Set “Experience mapped NL” check N.Radio, name used to “bg6500”; Set “IR mapping” IR command N.Radio to “BM6500 BLC”, “NL source” to “bg6500”.
3. forget the speakers attached to the BM6500. Attach them to the BM6500 BLC using a MCL2P/Beolink Active/ML-MCL converter as amplifier and add a IR eye to the BM6500 BLC.
4. BS9000 BLC – Moment; ASlave ; Set “IR mapping” IR command N.Music to “BS Moment”, “NL source” to “music”.
5. BS9000 BLC – Moment; ASlave ; Set “IR mapping” IR command Radio to “BS Moment”, “NL source” to “TuneIn”.

Then giving the CD command the BS9000 should start; Phono (=N.Radio) will start the bg6500; etc

Be aware that a ML source IR command can only be used once! So you are restricted to the commands available in the BLC (2 BLC doesn’t mean 2 times the available commands)

 

 

[Carolpa]

bnousr wrote:

I still utilise the BS6500 in the office and needs to have the speakers connected directly, and don’t care about audio from any other sources from either ML/NL devices.

Be aware with the proposed solution you can still listen to the speakers now connected to the BM6500, but then they are connected to the BM6500 BLC.

You can start all the sources of the BM6500 with a remote if an IR eye is connected to the BM6500 BLC (or use the B&o app) and play these sources to the Beovox 100 and Cona BLC connected

 

[Tignum]

Hi Carolpa! was hoping you would join :-). I was not saying one BLC would be enough, just that in principle you could use a BLC as an ML splitter (in the same ML chain) when required. Indeed the IR commands logic would be gordian knot needing a bit of untieing! Regards, Johan

[Carolpa]

Tignum wrote:

I was not saying one BLC would be enough,

Hi Johan, anyway I didn’t interpreted it that way.

just that in principle you could use a BLC as an ML splitter

but if the BLC can and will be used as splitter the settings of the BLC have to correspond (you will agree…)

Indeed the IR commands logic would be gordian knot needing a bit of untieing!

the point is: a BLC is more a converter to add ML products to NL, than a converter to add NL products to ML.

groet

[Tignum]

bnousr, Carolpa, out of curiosity, I put my BM6500 in option 1 and connected a speaker to it. The system, connected to 1611/BLC/A.SLAVE works as normal.

In another room (that uses my main ML chain) I could listen to, and control the BG CD 7000.

Also, when starting the BG CD 7000 (from stdby) from the other room, the speaker connected to the BM6500 stays muted.

This seems exactly what bnousr looks for. And to be honest, I would find it quite elegant to let the BM6500 amps drive the passive CX and Cona speakers (and not introduce another amp and leave the BM running idle).

Again, the above is not allowing the BM6500 play any other sources than its own.

As maybe said before, I think it’s really great that B&O allows to use all these generations of devices together. When it is all set-up (which takes a bit of fiddling) it can work really well.

Regards, Johan

[Tignum]

bnousr wrote:

the primary objective is to feed the audio from the Beosystem 65000 were the Beogram 6500 to the rest of the house which has my biggest interest, so don’t care about the Radio, CD or the cassette (well tape could be fun if it would be easy and without any conflict of commands being re-used) />

I think that A.TAPE is not a command that also exists under another name, so should be easily possible. Bonus!

[Carolpa]

Addition – an alternative:
BM6500 BLC (IR eye connected) still in ASlave; connect the BG6500 to LINE IN of BLC; Set in “IR mapping” N.Radio to the BM6500 BLC and the “NL source” to “LINE IN”.
Connect the PL-out of the BM6500 BLC to the AUX (or other connection) of the BM6500 (speakers connected; Steve will have a correct cable).
Restriction to this setup: you can not remote control the BG6500.

re-edit
as Johan below point out A.Slave works, so keep this setting.

[bnousr]

Finally got around to continue the config of the 2 BLC and were the original BLC is assigned to the Beosound Moment since it’s my only NL-device and the rest of my devices are ML-devices. And with the second BLC I’ve then assigning this to the Beosound 6500:

• Moment -> BLC-BSM and setup as source center
• BS6500 -> 1611 -> BLC-BS6 which is currently setup as Audio Slave

Previously in the thread it was mentioned to put the BLC-BSM as Audio Slave as well which I haven’t tried yet as I first want to share my config. Also, since it was mentioned that the Beosound 9000 was assumed to be connected to BLC which either was a typo if it was meant to be ref. to the Beosound 6500. So slightly confused.

Here are the config which I’m currently been using for several years for the BLC-BSM and the Beosound Moment:

And this is how the BLC-BS6 is currently setup which has the 1611 and Beosound 6500 connected to it:

[Tignum]

Hi bnousr, I think posting your settings is helping a lot!

In general, I think you should see the BLCs as filters to pass on sources from ML to NL and vice-versa.

In case of the BLC-BS6, the A.Slave setting means you can only pass on sources from its ML side onto NL side. As you only want to pass on the PHONO and the A.TAPE sources, you can ‘uncheck’ in the ‘Experience mapped to NL’ all the boxes apart from ‘N.RADIO’ and ‘A.MEM’ (as they are the same as PHONO and A.TAPE). At ‘Name used on NL’ you can call the N.RADIO source ‘PHONO’, and the ‘A.MEM’ source can be called ‘A.TAPE’. The BLC-BS6 will now pass these sources and commands onto the BLC-BSM that is connected to your main ML network. On the IR mapping page, assign the N.RADIO command to BLC-BS6 with NL source renamed PHONO. The A.MEM command is then to be assigned to BLC-BS6 with renamed NL source A.TAPE.

See my (simple) setting of the BLC connected to my BeoSystem 6500, just for passing on CD onto the NL side:

And the setting of the other BLC to push that CD signal onto its ML side:

 

As said I am wondering if you cannot better set the BLC-BSM as an A.Slave too, and only pass on the netradio and netmusic onto the main ML network as Carolpa already suggested. I would then assign the ‘RADIO’ IR command to the Beosound Moment’s ‘TuneIn’ NL source, and the ‘N.MUSIC’ (=A.TAPE2) command to the Beosound Moment’s ‘Music’ NL source.

The only thing that I can’t figure out is how the main ML network will react to a ‘RADIO’ IR command, as it might start the TuneIn radio on the BS Moment, as well as the FM radio of the BS9000. Or am I seeing that wrong Carolpa? Were you counting on a 3rd BLC?

bnousr, I hope this helps.

[bnousr]

Right, got around to do a bit more testing and I’ve setup the seconday BLC-BS6 in accordance with your suggestion so that ML source, A.MEM, points to A.TAPE (Name used on NL). But, what is not clear currently if the suggestion was to change so that the primary BLC, BLC-BSM, also is set to Audio Slave instead of as it’s currently, still, to Source Center. Which also would explain why I’m not able currently to get A.MEM enabled on the Source visible on ML list for the primary BLC-BSM:

And the IR mapping page has been cleaned up as well and looks like this now:

With the above settings I’m not getting any reaction when pressing A.MEM in other rooms which is connected to the Masterlink network nor in a Link room.

[Tignum]

Hi bnousr, you will need to bring the two new NL sources (A.TAPE and PHONO) to the ML side on your main ML network. I have tried to make more visual Carolpa’s earlier detailed suggestion (to correct if I made a misinterpretation):

As said, I do doubt if there will be no ‘RADIO’ command conflict, if so it could probably be fixed with a 3rd BLC, something like this:

which will be a bit more costly ofcourse. Maybe Carolpa or another more experienced can confirm the above / help to get it more complete to get you where you want to be. Regards, Johan

[bnousr]

Ok, makes far easier to grasp and thanks for the efforts which is highly appreciated! Based on that the BLC units could be considered a router for ‘link commands’ wouldn’t it be possible to then use A.MEM / BLC-BS6 / PHONO to trigger the BG6500 and just ditching the Beocord 6500?

Also, if it turns out that I would need to opt for an additional BLC to setup the system in accordance with the second schematics, would the BS9000 still work in option 0 as I don’t have any speakers connected (ref. to my previous schematic) to it but that it make use of speakers connected to the BV10?

[Tignum]

Hi again,

Goal should be to have the BeoSystem 6500 working as it is (and only lend the ML chain the Phono and Tape sources).

And yep, curious what others say.

But after you can get the system wired up with 3 BLCs like below, I am happy to set up an (evening) Teams call and set up all BLCs to get the whole factory running. I now want to see this working :-). Regards, Johan

[bnousr]

Right, I got now 2 additional BLC that I can use for testing here on my side, so I now have in total 4 units, so could give it a try. What you suggest in the above diagram is to add the third BLC unit for BS9000 and where the BLC-BV10 is what would be my BLC-BSM. Let me give it a try directly and see how it works out.

[bnousr]

And time for update, with 3 BLC in place, I’ve now got it to work with the suggested settings tht you provided Johan:

• BLC-BSM as Audio Master and pulls N.MUSIC (Music) from Moment
• BLC-BS6 as Audio Slave and pulls A.MEM (A.TAPE) but won’t do N.RADIO (PHONO) from BS6500
• BLC-BS9 as Audio Slave and pulls RADIO (RADIO)/CD (CD) from BS9000

So it seems that I just have to accept that N.RADIO has to be used to activate PHONO and it’s not possible to use any other command, for example V.MEM to activate PHONO?

Additionally, I’ve also got a DAC connected to the BS6500 via A.TAPE2 which potential could be pulled as well maybe using PC and pointing to A.TAPE2 (tried and won’t work).

Got to say this absolutely so cool being able to pull vinyl into the entire masterlink in the entire house which increases the WAF-factor significantly 🙂

[Author]

Posts