[Tignum]

Carolpa wrote:

Hi Johan could you post or PM me some settings of your Core/BLC? Everything I try/change ends with the same outcome…… only one connected device is visible! thx in advance Paul

Hi Paul, is there something specific you want to see? Let me know, J.

[Tignum]

It sure helps! I have to figure out, without having all the equipment, how this is all working.

The plan is to connect a BC2 with ML to BLC (audioslave) plus BS9000 with ML to BLC (audioslave) to allow a Core to play from either CD player! I know I can rename the sources in the BLCs, but I am not sure now if I can teach a (non BT) BR1 to distinguish them.

Hope someone fixed a similar problem and can help me.

Thx, Johan

[Carolpa]

Tignum wrote:

Hi Carolpa, was hoping for you posts! The planned set-up is not for me, but for a very friendly gentleman building a new house, that I am helping a bit to get all cabling (and user experience) right. The Core for that home is not yet purchased. (Here is an image of my own Core, that still seems to have the primary/secondary split still:

 

Okay, my Shape Core is programmed: primary connected – BS9000 BLC, the secondary -BC2 BLC.

As can be seen above the BS9000 sources can be chosen to be set as Shape sources, but the Beocenter 2 sources are missing in this list and therefor not available (they also do not show op in the B&o app/Halo). If the BC2 CD is not a source of the Shape Core, how to start this source with a BR1?

If you start the same setting page as mine above, do you get all the sources? The sources from your Beosound 5 AND the sources of the Beosystem 6500 can be ticket and set as Core sources?

Software is 2.4.55189.229090071,

Same over here

let me now what other settings you would need. Again, this is my (older) Core, that I do not control with a BR1, but use (only) to feed B&O radio and DLNA Music to two ML networks. The other Core will be bought later.) I think it will not be the end of the world if it is not possible to play from 2 different CD players. I expect the BC2 to be used way less often than the BS9000.

I can start the BC2 CD with the B&o app by chose the Beocenter 2 BLC, go to the BLC sources and chose CD. The CD starts. Then JOIN the Shape Core (for example).
Note: this method works in general with BLC and the B&o app. Only a T1611 connected Beosystem 7000 does not respond momentarily.

Priority is that the Core is away in quite remote utility room to bring all technical cable clutter out of the living space. But if there is way, why not!

Using the app makes it possible to start both CD players and you can hide the Core anywhere.

[Tignum]

This made me thinking – could I bridge BlueTooth communication over Ethernet, something like this:Has anyone attempted something like this?

Thanks, Johan

[Millemissen]

Sorry for interfering once again.
But I am a proponent for simple solutions!

Question – aren’t you going to install speakers in the room, where that link eye is supposed to be?
You wrote about BL5’s, that are going to be connected digital….if I understood that correct!
This would mean cable runs from the room where the Core is supposed to be located!
Not just for the ir eye and the digital connection, but also – in that case – for the required Powerlink cables.

The Core is a rather small box – it should be rather easy to hide that in the actual room and thereby have less cable runs.
And it would be in reach of the BROne without any problems (or fancy solutions).

Or is there still something that I missed?

MM

[Tignum]

Hi MM, your observations are correct (and appreciated). The remotely positioned Core will require much longer S/PDIF and PL cables indeed. But having no cable clutter in the Living room is priority. Hence the IR eye (with BR1 limitations) or the above idea (unsure if feasible). Thanks! Regards, Johan

[Carolpa]

But to me, within ~1 second seems to be impossible to address 3 BLC’s!

[Tignum]

Hi Paul, are you a magician? :-). That must have been the system logging that time I guess.

How many do you have?! Me four…

Johan

[Tignum]

Tignum wrote:

Millemissen wrote:

@Tignum I do not understand the need/wish for an ir eye in this case. You (he) would need to have the eye some where reachable for the Beo4 including cabling. If someone want to hide a Core away, he IMO should go for a BROne/BT instead. Or is there something, that I don’t understand in the setup? MM

Hi MM, the Core will be placed in a utility room, easily 10-15m away from the living room, one level down. I am not expecting the Bluetooth signal to cover that distance. That is the reason to bring a wired (IR) sensor to the living room. I expect a much more reliable control this way. We already made peace with the idea that the CD command of the BR1 will be reserved for the BeoSound 9000. Still, playing from the BeoCenter 2 CD should be possible using the app. Thanks as always! Johan

Hello again MM, yesterday I played a bit with the Core and the BR1 BT (never really did that before – I bought the BR1 to control my BS3 with ‘navi’ in the first place). But it is really nice! With the radiostations in the screen, all source names etc. Hmmm – let at least keep all options open.
Regards,
Johan

[Tignum]

Millemissen wrote:

@Tignum I do not understand the need/wish for an ir eye in this case. You (he) would need to have the eye some where reachable for the Beo4 including cabling. If someone want to hide a Core away, he IMO should go for a BROne/BT instead. Or is there something, that I don’t understand in the setup? MM

Hi MM, the Core will be placed in a utility room, easily 10-15m away from the living room, one level down. I am not expecting the Bluetooth signal to cover that distance. That is the reason to bring a wired (IR) sensor to the living room. I expect a much more reliable control this way. We already made peace with the idea that the CD command of the BR1 will be reserved for the BeoSound 9000. Still, playing from the BeoCenter 2 CD should be possible using the app.
Thanks as always! Johan

[Tignum]

Hi,

It is not installed yet – for now it exists only in the above chart :-). We will have to wait a little before testing this.

I do actually hope the Bluetooth connection between BR1 BT and Core is so strong that the above is not necessary. (Will investigate ‘bridging/meshing’ Bluetooth in the meantime).

B&O support actually hinted that what we want to achieve is complicated, and a B&O installer should be consulted.

We will have to be a bit patient I guess.

Thanks for thinking with us! Regards, Johan

[Carolpa]

Tignum wrote:

Hi, It is not installed yet – for now it exists only in the above chart :-). We will have to wait a little before testing this. I do actually hope the Bluetooth connection between BR1 BT and Core is so strong that the above is not necessary. (Will investigate ‘bridging/meshing’ Bluetooth in the meantime). B&O support actually hinted that what we want to achieve is complicated, and a B&O installer should be consulted. We will have to be a bit patient I guess. Thanks for thinking with us! Regards, Johan

Hi Johan,

I was hypothetical speaking: “now the…”.
Just out of curiosity, why do you think you won’t have the same issues if a BR1bt is used?

regards

[Tignum]

Hi, I am assuming that then the BR1 will show the (in the app selected) NL sources (with the names given in the BLC settings) under the MUSIC button.

To your other question on the IR based communication in the diagram – the expectation is that ‘CD’ will start the Bs9000 and ‘[Link symbol]CD’ will start the BC2.

It is a pity that the Core does not have the settings page to link IR commands to NL sources as the BLC has!

Maybe something for the development team?

Regards, Johan

 

[Carolpa]

Tignum wrote:

Hi, I am assuming that then the BR1 will show the (in the app selected) NL sources (with the names given in the BLC settings) under the MUSIC button.

That’s an interesting assumption.
For sure this principle works for a BR Halo. But than the communication is completely different. I do not know how a BT remote communication works in comparison to a normal IR. Does it compares to IR or does it compares to the Halo type?

To your other question on the IR based communication in the diagram – the expectation is that ‘CD’ will start the Bs9000 and ‘[Link symbol]CD’ will start the BC2.

I did a simple test: I placed the BLC IR option to 4 and the BS3000 in option 2. Connected a IR eye to the BLC. Then I gave a LINK CD command. The BS3000 did not start to play the cd.

It is a pity that the Core does not have the settings page to link IR commands to NL sources as the BLC has! Maybe something for the development team? Regards, Johan

[Darkstar101]

Hallo,

an mein Beomaster 7000 funktioniert der rechte Powerlinkausgang nicht mehr.

Ich betreibe an der Anlage zwei Beolab 8000.

Ich suche jemanden der das reparieren kann.

Standort: Germany, Rheinland -Pfalz, Nähe Koblenz

Grüße Richard

[Tignum]

Hi Darkstar101, it seems your post was not meant for this thread? Regards, J.

[Tignum]

Hi Carolpa,

To illustrate:

Name the CD source CD6500Carolpa in the BLC:Make it available in the Core:

And seeing it on the BR1 (under MUSIC)

So Bluetooth would be the best! (as MM already said). Regards, Johan

[Tignum]

Hi all, after a dialogue with B&O support on the meaning of the sources ‘CD’ and ‘[Link symbol]CD’, we came to this outcome:

where the trick lies in Option 5 setting of the BC2.

The proof will be in the pudding I guess. For now it seems that this enables:

• Using a Core for PowerLink and S/PDIF signal paths
• Tucking the Core far away by using an IR eye
• Using two ‘CD’ commands for two CD sources under the MUSIC button of the BR1 in ‘BeoSound’ mode

Regards, Johan

With ‘Link symbol’ I mean this:

[Carolpa]

Tignum wrote:

Hi all, after a dialogue with B&O support on the meaning of the sources ‘CD’ and ‘[Link symbol]CD’, we came to this outcome: where the trick lies in Option 5 setting of the BC2. The proof will be in the pudding I guess. For now it seems that this enables:

• Using a Core for PowerLink and S/PDIF signal paths
• Tucking the Core far away by using an IR eye
• Using two ‘CD’ commands for two CD sources under the MUSIC button of the BR1 in ‘BeoSound’ mode

Regards, Johan With ‘Link symbol’ I mean this:

Hi

Now the system is installed and programmed as proposed and the CD command is given in the BL5 room.
Which CD-player starts? How does the system differentiate which CD-player should start?
Where in the Core, where in one of the two BLC’s does “option 5” decide to select the BS9000 or the BeoCenter 2?

Rethought my earlier response:

Now the system is installed and programmed as proposed and the CD command is given in the BL5 room. It will start the BS9000. But can you start the BeoCenter 2 because it is a local source in the ML of the other room and cannot be distributed? At least that was the case when everything was ML. Now the Beocenter 2 is ML connected to NL so the source will be available on NL.

But still you need a command to start the BeoCenter 2 in the BS9000 room. So you still have the same “problem”.

Note you can JOIN the Core if the BC2 is already playing

[Author]

Posts