Beolink ML/NL version number? 1.4, 1.3

Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors
Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • #42056
    XavierItzmann
    BRONZE Member
      • Topics Started 22
      • Total Posts 155

      Thank you Johan.

      I’ll be asking any sellers about the software version installed on their BeoLink Converter NL/ML, and will only buy if it is 1.4.3.19864 or higher.

      #42054
      XavierItzmann
      BRONZE Member
        • Topics Started 22
        • Total Posts 155

        So, I need one of these as I was away during the transition years and all my old equipment is MasterLink and B&O no longer sells this critical component. Is it true that these are no longer consumer updatable? What’s a man to do then?

        If I buy one, is there a minimum version I should get? Are there substantial performance differences? I found an old post here in the forum that cited the final version number but then I lost it.

        Thanks in advance.

        #42057
        Rolf2
        BRONZE Member
          • Germany
          • Topics Started 2
          • Total Posts 72

          Hello Xavier,

          Johan has mentioned what is to my knowledge the final sw version. Last year, I had to order a repair of one of my BLC ´ s and they needed to exchange the electronics completely. So, more or less a new unit, and it says sw is on 1.4.3.19864. You should be careful indeed, and buy only a BLC with the latest sw version. If it is on a lower level sw version, it may be so because of faulty electronics.

          The sw versions of the BLC are, from latest to older:

          1.4.3.19864 – Final version

          1.4.3.19816

          1.4.2.19611

          1.4.1.19522

          Those are the ones I know about.

          Kind regards,

          Rolf

          #42055
          Tignum
          GOLD Member
            • Netherlands
            • Topics Started 8
            • Total Posts 368

            Hi Xavier,

            Both my BLCs are “1.4.3.19864, December 11, 2015” and they work fine.

            Hope this helps. Regards, Johan

            #42058
            XavierItzmann
            BRONZE Member
              • Topics Started 22
              • Total Posts 155

              Ahh, yes, Rolf, thanks for your detailed advice. The current range of Connected products is set by default on software “auto-update”, so when devices currently updated by B&O cease to be upgraded, most will be left on the final version.

              Which prompts me to ask… at the time the BLCs were current, did “auto-update” exist? Because then you’d be doubly right to question the full functionality of items being sold with less than the final version!

              (unless the devices were stored in a drawer, one might think).

              #42059
              Millemissen
              BRONZE Member
                • Flensborg————Danmark
                • Topics Started 23
                • Total Posts 1,065

                552E138C-71EF-49A3-A7F4-8916968CFCFB

                Just checked….

                MM

                #42060
                XavierItzmann
                BRONZE Member
                  • Topics Started 22
                  • Total Posts 155

                  Thanks, MM!

                  Since these BLC’s had recommended auto-update, most good ones should be on 1.4.3.19864!

                  Now I just have to get one.

                  #42061
                  Rolf2
                  BRONZE Member
                    • Germany
                    • Topics Started 2
                    • Total Posts 72

                    Go and grab one and enjoy your ML products working together with NL products!

                    Kind regards,

                    Rolf

                  Viewing 8 posts - 1 through 8 (of 8 total)
                  • You must be logged in to reply to this topic.